Raw file format provides slightly better performance while qcow2 offers advanced features such as copy on write and Live_Snapshots. To your config file at /etc/pve/qemu-server/.conf, see the vfio blog Further information Disk-Image Format: raw vs qcow2 If you are using a GPU via PCI(e) passthrough, you might need to add Make sure to set your processor to 'host' if you already set up your VM and did not select 'host' as processor, you can change it in the 'Hardware' section of your VM in the web interface. To run WSL (Windows Subsystem for Linux) you need to enable Nested Virtualization. Once a driver has been found you might be prompted with a security warning asking if you "Would like to install this device software".Press the Mount button and your virtual disk drive with mounted image. Make sure that "Include subfolders" is checked. For example, you can enable the option to mount a drive as removable media, set drive type (HDD, CD, etc.), drive letter, etc. Select "Browse my computer for driver software".Go to the Device Manager to see if there are any drivers missing. The installer is located on the driver CD under guest-agent\qemu-ga-x86_64.msi. To remedy this install the "Qemu Guest Agent". If you enabled the Qemu Agent option for the VM the mouse pointer will probably be off after the first boot. Install Guest Agent and Services Guest Agent HINT: There is a video showing the process for a Windows Server 2016 installation which is the same as for Windows 10. Choose the drive and continue the Windows installer steps.With these three drivers you should be good covered to run a fast virtualized Windows 10 system. Memory Ballooning: Again, repeat the steps but this time select the "Balloon\w10\amd64" folder, then the "VirtIO Balloon Driver" and install it by clicking next.Network: Repeat the steps from above (click again "Load driver", etc.) and select the folder "NetKVM\w10\amd64", confirm it and select "Redhat VirtIO Ethernet Adapter" and click next.Select the "Red Hat VirtIO SCSI pass-through controller" and click next to install it. Hard disk: Browse to the CD drive where you mounted the VirtIO driver and select folder "vioscsi\w10\amd64" and confirm.Now click "Load driver" to install the VirtIO drivers for hard disk and the network.Follow the installer steps until you reach the installation type selection where you need to select "Custom (advanced)".After starting your VM launch the noVNC console.Now your ready to start the VM, just follow the Windows installer.Load the Virtio Drivers ISO in the new virtual CDROM drive. For the VirtIO drivers, upload the driver ISO (use the stable VirtIO ISO, download it from here) to your storage, create a new CDROM drive (use "Add -> CD/DVD drive" in the hardware tab) with Bus "IDE" and number 0.Configure your memory settings as needed, continue and set "VirtIO (paravirtualized)" as network device, finish your VM creation.Set "Write back" as cache option for best performance (the "No cache" default is safer, but slower) and tick "Discard" to optimally use disk space (TRIM). For your virtual hard disk select "SCSI" as bus with "VirtIO SCSI" as controller.Continue and mount your Windows 10 ISO in the CDROM drive Create a new VM, select "Microsoft Windows 10/2016/2019" as Guest OS and enable the "Qemu Agent" in the System tab.To obtain a good level of performance, we will install the Windows VirtIO Drivers during the Windows installation. It should say status is Onlineĥ.This is a set of best practices to follow when installing a Windows 10 guest on a Proxmox VE server 6.x. I was trying to do this using Hyper-V 2012 Core and to offline the USB drive:Ĥ. Rightclick on the Frontrow (where it say's "Disk 1" e.g.) select "Offline".Īn addition from JonE (Thx for that Jon): Rightclick on the appropriate Partition(s) in the Graphical View (right lower pane), select "Change Drive Letter an Paths.", click on Removebutton. Dataloss is possible, you've been warned. If you don't know what Diskmanager is good for, or what a Partition is, you should better stop reading right now. Connect your USB-Drive, wait until you can access the Drive in Explorer.Įxpand Storage, click on Disk Management.
0 Comments
Leave a Reply. |